List of Publications

 

Total Journals - 34

Total Conferences - 52

1.      Ravindra I. B., Narendranath S, Srinath M. S., “Joining of Inconel-625 alloy through microwave hybrid heating and its characterization”, Journal of Manufacturing Process, 18, 2015, 117-123.
2.      Ajit M. Hebbale, Srinath M.S., “Microstructural Investigation of Ni based cladding developed on austenitic SS-304 through microwave irradiation”, Journal of Material Research and Technology, 5(4), 2016, pp. 293-301.
3.      AjitHebbale, Srinath M. S., Microstructure and Experimental Design Analysis of Nickel Based Clad Developed Through Microwave Energy, Perspectives in Science, 8 (2016): 257-259.
4.      AjitHebbale, Srinath M. S., “Taguchi analysis on erosive wear behavior of cobalt based microwave cladding on stainless steel AISI-420”, Measurements, 99, 2017, pp. 98-107.
5.      Ravindra I. B., Narendranath S, Srinath M. S., “Microstructure and Mechanical Properties of Inconel-625 Welded Joint Developed through Microwave Hybrid Heating”, Proceedings of the Institution of Mechanical Engineers, Part B, J. of Engineering Manufacture (Accepted).
6.      Shashank Lingappa M., Srinath MS, Amarendra HJ, "Microstructural Investigation and Characterization of Bulk Brass Melted by Conventional and Microwave Processing Methods." Materials Science Forum, 890, 2017, pp. 356-361.
7.      Shashank Lingappa M., Srinath M. S., Amarendra H. J., “Melting of 60Sn40Pb alloy using microwave energy and its characterization”, Materials Today Proceedings, 4(2), 2017, pp. 471-476.
8.      Hemanth S Thulasi, Dr. Y. Arunkumar, Srinath M. S., Rakshith T, “Manufacturing Simulation for determining the influence of Process Parameters on Quality of Forgings”, NCERAME 2015 Proceedings, International Journal of Engineering Research and Technology, 2015,146-151.
9.      Srinath M. S., Ajit M. Hebbale, Anand N K, Kiran Kumar U N, Kallesha K N, Kotresh M S, “Evaluation of Erosion Behaviour of Ni based Cladding developed through Microwave Energy, NCERAME 2015 Proceedings, International Journal of Engineering Research and Technology, 2015, 202-206.
10.  AmitkumarAdvekar, Dr. Y. Arunkumar, Srinath M. S., “Simulation of high pressure die casting process for identifying and minimizing defects”, , NCERAME 2015 Proceedings, International Journal of Engineering Research and Technology, 2015, 442-450.
11.  Ajit M Hebbale, Srinath M.S., “Microstructural Characterization of Ni based Cladding on SS-304 Developed through Microwave Energy”, Materials Today Procedings, 2015, 2, 1414-1420.
12.  Rajesh N. L., M. S. Srinath, “Remote home security and automation system using zigbee based multi-bounce communication, IJIRT, 2015, 2 [3], 145-150.
13.  Roshny Mathew, M.S. Srinath, N.S. Jyothi, “Automation of Electrical Power Distribution System”, i-manager’s Journal on Power Systems Engineering, 2015, 3 [2], 34-40.
14.  Sharath Chandra H.S, Y Arun Kumar and Srinath M.S., Multi-Level Dynamic Job Sorting for Increasing Productivity Using Discrete Event Simulation (Diverging Conveyors), International Journal of Engineering Research and Development, 2015, 11[11],75-81. 
15.  Hemanth S Thulasi, Y. Arunkumar and M.S.Srinath, Design and Manufacturing Simulation of Preform for Thread Rolling Operation, International Journal of Modern Engineering Research (IJMER), 2015, 5 [10], 60 -68
16.  Gouthama T. R., Harisha G., Manjunatha Y. R., Mohana Kumara S. M., Srinath M. S., Shashank Lingappa M., “Melting of tin using muffle furnace and microwave energy and its characterization”, IOP Conference Series: Materials Science and Engineering, 149,2016.
17.  Srinath M. S., Ajit M. Hebbale, “Fuzzy prediction of slurry erosive behavior of cobalt based clad developed through microwave energy”, Materials Today Proceedings, 4(2), 2017, pp. 1804-1811..
18.  Y. Arunkumar,  S. Murali, The Effect of Pre-Ageing on the Delayed Ageing  of Al-7Si-0.3 Mg, Journal of Metals, PP. 29-33, February 1997.
19.  Y.Arunkumar, Rajashekar Patil, S. Mohankumar, “Discrete Event Simulation for Increasing Productivity in Digital Manufacturing”, International Journal of Engineering Research and Development (IJERD), ISSN: 2278-067X, Volume 1, Issue 10 (June 2012), PP.36-40.
20.  Hemanth S Thulasi, Y. Arunkumar, Srinath M. S., Rakshith T, “Manufacturing Simulation for determining the influence of Process Parameters on Quality of Forgings”, NCERAME 2015 Proceedings, International Journal of Engineering Research and Technology, 2015,146-151.
21.  Hemanth S Thulasi, Y. Arunkumar and M.S.Srinath, Design and Manufacturing Simulation of Preform for Thread Rolling Operation, International Journal of Modern Engineering Research (IJMER), 2015, 5 [10], 60 -68
22.  Hemanth T S, Arunkumar Y, Srinath M.S, Rakshith T, “Manufacturing Simulation for determining the   Influence of Process Parameters on quality of forgings”,. International Journal of Engineering Research & Technology (IJERT), NCERAME-March 2015,PP. 146-151.
23.  AmitkumarAdvekar, Arunkumar Y, Srinath M.S. ,”Simulation of High Pressure Die Casting Process for Identifying and Minimising Defects”, International Journal of Engineering Research & Technology (IJERT),NCERAME-March 2015,PP..442-450.
24.  Sharath Chandra H.S, Y Arun Kumar and Srinath M.S., Multi-Level Dynamic Job Sorting for Increasing Productivity Using Discrete Event Simulation (Diverging Conveyors), International Journal of Engineering Research and Development, 2015, 11[11],75-81. 
25.  Sharath Chandra H.S, Y Arun Kumar and Srinath M.S, Effect of operational parameters in a converfing conveyor system  for an Assembly Operation, International Journal of Innovative Research in Science, Engineerinng and Technology,  2016, 03, Vol 5.  3698-3705
26.  H.V.Divya, L. LaxmanaNaik, B.Yogesha, “Processing Techniques of Polymer Matrix Composites – A Review”International Journal of Engineering Research and General Science Volume 4, Issue 3, May-June, 2016
27.  H.R. Deepika, B. Yogesha, H.V. Ramakrishna,An Effective Algorithms for Optimization of Process Planning and Scheduling: A Review” International Journal of Engineering Research and General Science Volume 4, Issue 4, July-August, 2016
28.  Hemanth S Thulasi, Dr. Y. Arunkumar, Srinath M. S., Rakshith T, “Manufacturing Simulation for determining the influence of Process Parameters on Quality of Forgings”, NCERAME 2015 Proceedings, International Journal of Engineering Research and Technology, 2015,146-151
29.  Hemanth S Thulasi, Y. Arunkumar and M.S.Srinath, Design and Manufacturing Simulation of Preform for Thread Rolling Operation, International Journal of Modern Engineering Research (IJMER), 2015, 5 [10], 60 -68
30.  Hemanth T S, Arunkumar Y, Srinath M.S, Rakshith T, “Manufacturing Simulation for determining the   Influence of Process Parameters on quality of forgings”,. International Journal of Engineering Research & Technology (IJERT), NCERAME-March 2015, 146-151.

 

Copyright